manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 91 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 91

ADSP-214xx SHARC Processor Hardware Reference

2-13 

I/O Processor

Bit 19 of the chain pointer register is the program controlled interrupt 
(

PCI

) bit. This bit controls whether an interrupt is latched after every 

DMA in the chain (when set = 1), or whether the interrupt is latched after 
the entire DMA sequence completes (if cleared = 0). If a program contains 
a single chained DMA then the PCI interrupt is generated coincident with 
the start of next TCB loading.

However, if running multiple DMA channels this coincidence is no longer 
true since there are different DMA channel priorities versus interrupt 
priorities.

The 

PCI

 bit only effects DMA channels that have chaining enabled. 

Also, interrupt requests enabled by the 

PCI

 bit are maskable with 

the 

IMASK

 register.

TCB Storage

This section lists all the different TCB memory allocations used for DMA 
chaining on the peripherals. Note that all TCBs must be located in inter-
nal memory except SPORTs, where TCBs can exist in external memory.

Table 2-13. FFT Input Chain Pointer Register (CPIFFT)

Bit

Name

Description

18–0

IIx address

Next chain pointer address

19

PCI

Program controlled interrupt
0 = no interrupt after current TCB
1 = interrupt after current TCB

20

COEFFSEL

Coefficient select for next TCB
0 = next TCB is data TCB
1 = next TCB is coeff TCB

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments