manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 485 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 485

ADSP-214xx SHARC Processor Hardware Reference

10-27 

Serial Ports

Figure 10-4

 illustrates framed serial transfers.

Early Versus Late Frame Syncs

Frame sync signals can be early or late. Frame sync signals can occur dur-
ing the first bit of each data word or during the serial clock cycle 
immediately preceding the first bit. The 

LAFS

 bit of the 

SPCTLx

 control 

register configures this option.

When 

LAFS

 is cleared (=0), early frame syncs are configured. This is the 

normal mode of operation. In this mode, the first bit of the transmit data 
word is available (and the first bit of the receive data word is latched) in 
the serial clock cycle after the frame sync is asserted. The frame sync is not 
checked again until the entire word has been transmitted (or received). In 
multichannel operation, this is the case when the frame delay is one.

If data transmission is continuous in early framing mode (for example, the 
last bit of each word is immediately followed by the first bit of the next 
word), the frame sync signal occurs during the last bit of each word. Inter-
nally-generated frame syncs are asserted for one clock cycle in early 
framing mode.

Figure 10-4. Framed Versus Unframed Data

B

3

B
2

B

1

B
0

B

3

B
2

B

1

B
0

B

3

B
2

B

1

B
0

B

3

B
2

B

1

B
0

B

3

B
2

B

1

SPORTX_CLK

FRAMED

DATA

UNFRAMED

DATA

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments