manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 509 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 509

ADSP-214xx SHARC Processor Hardware Reference

10-51 

Serial Ports

The SPORT generates an interrupt when the transmit buffer has a 
vacancy or the receive buffer has data. To determine the source of an 
interrupt, applications must check the transmit or receive data buffer sta-
tus bits (

DXS_A

, 

DXS_B

) in 

SPCTLx

 registers and for DMA the corresponding 

status bits in the 

SPMCTLx

 registers. However note in most cases if both 

channels are enabled with the same DMA count, there is no need to check 
the status since both channel interrupts are close to each other.

Standard DMA does not function properly in I

2

S/left-justified 

mode when two channels (A and B) are enabled with different 
DMA count values. In this case, the interrupt is generated for the 
least count only. If both the A and B channels of the SPORTs are 
used in I

2

S/left-justified mode with DMA enabled, then the DMA 

count value should be the same for both channels. This does not 
apply to chained DMA.

Error Detection

Similar to previous SHARC processors, the SPORTs can return the status 
of data buffer underflow and overflow conditions. Additionally, the 
SPORTs can also detect frame syncs that are occurring early, even before 
the last transmit or receive completes. To detect these errors, the processor 
has an error interrupt (SPERRI vector interrupt) that is shared for all 
SPORTs together. It is triggered on a data underflow, data overflow, or 
frame sync error in their respective channels. An interrupt is triggered and 
programs simply read the 

SPERRSTAT

 register which reduces the processor 

overhead needed to do register polling. If the interrupt enable bit 

SPERRI

 

is set then the interrupt is raised when the error occurs. Otherwise, the 
errors are latched and no interrupt is generated. 

As shown in 

Figure 10-10

, the frame sync error (which sets the error bit) 

is triggered when an early frame sync occurs during data transmission or 
reception or for late frame sync if the period of the frame sync is smaller 
then the serial word length (

SLEN

). However, the current transmit/receive 

operation continues without interruption. 

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments