manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 268 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 268

Clocking

4-4

ADSP-214xx SHARC Processor Hardware Reference

Status Registers (LSTATx).

 Programs can see several aspects of link port 

operation using the status registers. These include bus status, buffer status, 
receive and transmit status, and errors.

Clocking

The link port clock is derived from the clock out generator based on the 
linkport to core clock ratio. 

For more information, see “Output Clock 

Generator” on page 22-5.

The link port to core clock ratios (1:2, 1:2.5, 1:3, 1:4) can be programmed 
in the 

PMCTL

 register. This programming is applicable only for the trans-

mitter. The receiver can operate at any asynchronous frequency up to the 
maximum frequency, independent of the ratio programmed.

Functional Description

Each link port, shown in 

Figure 4-2

, consists of eight data lines (

LDATx7–0

, 

x = 0, 1), a link port clock line (

LCLKx

), and a link port acknowledge line 

(

LACKx

). The 

LCLKx

 and 

LACKx

 pins of each link port allow handshaking for 

asynchronous data communication between DSPs. Other devices that fol-
low the same protocol may also communicate with these link ports.

The link port operates in half-duplex mode, only receive or transmit oper-
ation can happen per linkport by using core or DMA. If full-duplex 
operation is required both linkport must be used.

In receive operation, the data are received by the external receive buffer 
packed into 32-bit format and shifted to the internal receive buffer. The 
core or DMA read the data from the internal buffer. In transmit opera-
tion, the data are written to the internal transmit buffer moved to the 
external transmit buffer to shift the data off-chip.The following sections 
provide details on theis interface.

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments