manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 475 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 475

ADSP-214xx SHARC Processor Hardware Reference

10-17 

Serial Ports

As shown in 

Figure 10-3

 the SPORT uses two control signals to sample 

data.

1. Serial clock (

SCLK

) applies the bit clock for each serial data.

2. Frame sync (

FS

) divides the incoming data stream into frames.

Frames define the required data length (after the serial to parallel conver-
sion) necessary to store the data in memory for further processing as 
shown in 

Figure 10-3

. The transmitter for example drives clock and frame 

sync called master while the receiver is slave sampling these data.

After the slave is sampled the 

FS

 the 

SLEN

 word counter is reloaded to the 

maximum setting. Each 

SCLK

 decrements the 

SLEN

 counter until the full 

frame is received. If the transmitter drives the frame sync and data on the 
rising edge, the falling edge is used to sample the frame sync and data, and 
vice versa.

Figure 10-3. Frame Sync  and Data Driven on Rising Edge

DRIVE 
SCLK

SDRIVE
DATA

DRIVE 
FS

D7

D6

D5

D4

D3

D2

D1

D0

7

6

5

4

3

2

1

0

D7

D6

D5

D4

D3

D2

D1

D0

SAMPLED
FS

SAMPLED 
DATA

SLEN
COUNTER

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments