manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 339 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 339

ADSP-214xx SHARC Processor Hardware Reference

6-43 

FFT/FIR/IIR Hardware Modules

Chain Pointer DMA

The DMA controller supports circular buffer chain pointer DMA. One 
transfer control block (TCB) needs to be configured for each channel. The 
TCB contains:

• A control register value to configure the filter parameters for each 

channel

• DMA parameter register values for the input data (delay line) 

• DMA parameter register values for coefficient load

• DMA parameter register values for output data

• Intermediate results in multi-iteration mode are saved in the out-

put buffer

As shown in 

“FIR Accelerator TCB” on page 2-16

 and 

Figure 6-7

, the 

accelerator loads the TCB into its internal registers and uses these values 
to fetch coefficients and data and to store results. After processing a win-
dow of data for any channel, the accelerator writes back the appropriate 
values to the 

IIFIR

 and 

OIFIR

 fields of the TCB in memory, so that data 

processing can begin from where it left off during the next time slot of 
that channel.

The writeback value for input buffer is:

• IIFIR + W for single rate filtering.

• IIFIR + W 

×

 

M for decimation (M = decimation ratio).

• IIFIR + W/L for interpolation (L = interpolation ratio).

• The writeback values for output buffer in floating point mode is: 

OIFIR + W.

• The writeback values for output buffer in fixed point mode is: 

OIFIR + 3 

×

 W.

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments