manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 255 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 255

ADSP-214xx SHARC Processor Hardware Reference

3-125 

External Port

3. For a chained DMA, new TCB loading can be inhibited by clearing 

the 

CHEN

 bit while keeping all other control bits the same. The new 

TCB is loaded once 

CHEN

 bit is re-enabled. The TCB load which 

was happening when 

CHEN

 was cleared will complete.

4. Before initializing a chained DMA (including delay line) make sure 

that the 

ICEP

 and 

ECEP

 registers are zero.

5. The DMA parameter registers (except 

DMACx

) should not be written 

to while chaining is occurring (the 

CHS

 bit is set), but any register 

can be read during chaining.

6. A zero count for the 

ICEP

, 

RCEP

 and 

TCEP

 registers is forbidden. If a 

chain pointer with such a descriptor is programmed then the DMA 
might hang. So a read count zero or a write count zero for a delay 
line DMA is also forbidden.

AMI Initialization

After reset, the 

SDCLK

 is running with the default PLL settings. However, 

the AMI must be configured and initialized. In order to set up the AMI, 
use the following procedure. Note that the registers must be programmed 
in order.

1. Chose a valid 

CCLK

 to 

SDCLK

 clock ratio in the 

PMCTL

 register.

2. Assign external banks to the AMI using the 

EPCTL

 register (default).

3. Wait at least 8 

PCLK

 cycles (effect latency).

4. Enable the global 

AMIEN

 bit and program the AMI control 

(

AMICTLx

) registers. (Define control settings for AMI based on 

SDCLK

 speed and asynchronous memory specifications.

The 

AMIMS

 and 

AMIS

 bits 1–0 of the AMI status register (

AMISTAT

) can be 

checked to determine the current state of the AMI. 

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments