manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 125 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 125

ADSP-214xx SHARC Processor Hardware Reference

2-47 

I/O Processor

Internal Transfer Completion

This mode of interrupt generation resembles the traditional SHARC 
DMA interrupt generation. The interrupt is generated once the DMA 
internal transfers are complete, independent of whether the DMA is a 
transmit or receive. Therefore, for external transmit DMAs, when the 
completion interrupt is generated there may still be an external access 
pending at the external DMA interface. 

The I/O processor only generates a DMA complete interrupt when 
the channel’s count register decrements to zero as a result of actual 
DMA transfers. Writing zero to a count register does not generate 
the interrupt. To stop a DMA preemptively, write a one to the 
count register. This causes one additional word to be transferred or 
received, and an interrupt is then generated.

Access Completion

A DMA complete interrupt is generated when accesses are finished. For an 
external write DMA, the DMA complete interrupt is generated only after 
the external writes on the DMA external interface are complete. For an 
external read DMA, the interrupt is generated when the internal DMA 
writes are complete. In this mode the DMA interface can be disabled as 
soon as the interrupt is received. 

This mode is supported by the SPORT, SPI, link ports, and external port.

Core Single Word Transfer Interrupts

When a DMA channel’s buffer is not being used for a DMA process, the 
core can generate an interrupt on single word transfers (writes or reads) of 
the buffer of the respective peripheral. This interrupt service differs 
slightly for each peripheral. In this case, the peripheral’s buffer generates 
an interrupt when data becomes available at the receive buffer or when the 
transmit buffer is not full (when there is room for the core to write to the 
buffer). Generating interrupts in this manner lets programs implement 

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments