Agilent Technologies 81250 System Programming Manual And Scpi Reference Download Page 328

Page: 328 / 377

Concepts

Segment Import and Export Language

Agilent 81250 Parallel Bit Error Ratio Tester, Programming Reference, March 2006

327

Using Base w

Consider the following portion of import language code:

:statePar: { {B "0 x1")

#define state set B to have coding "0 x1"

:stateSet: B

#select State set B

:base: w

#use waveform characters

:vectorWidth: 5

#vector is 5 states wide

:vectors:

{

001xx

#this is the vector

}

Let us examine the

:statePar:

statement. A state set name B is

associated with the coding “0 x1”. The order of the characters “0 x1” is

particularly important as it implies the underlying binary values.

Starting with 0, the coding assumes increasing order from left to right.

Each of the waveform characters represents a state. To represent

three waveform characters, two bits are required. With two bits there

are 4 binary values available. The value 01 must be represented by

‘blank’ because this is not a valid waveform character. Therefore, the

binary values of the states are: 0 = 00, ‘blank’= 01, x = 10 and 1 = 11.

Enough information is now available to decode the vector: 001xx = 00

00 11 10 10

Here is the same example using a hexadecimal base and the coding

“0 x1”:

Coding

Memory Representation

Hardware Representation

‘blank’

n/a

Don’t care

Coding

Memory Representation

Hardware Representation

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 81250


























































































































































































































































































































































































Search results

Summary of Contents for 81250

Reviews:

Brands by name

Popular brands

Agilent Technologies 81250, System Programming Manual And Scpi Reference

Search results

Summary of Contents for 81250

Reviews:

Brands by name

Popular brands