Toshiba TOSVERT VF-S15 series, Инструкция по эксплуатации

Страница: 355 / 394

E6582175
M-3
[Trip information]
Error code Failure code Name Description Remedies
*

0020 Over-torque trip 1 
Over-torque reaches to a detection level
during operation.

Enable

(over-torque trip selection).

Check system error.

0041 Over-torque trip 2 
Output current reached f601 or more
and maintain in f452 during power
running.

Power running torque reached f441 or
more and maintain in f452 during
power running.

Reduce the load.

Increase the stall prevention level or
power running torque limit level.
*

0048 Over-torque /
Overcurrent fault 
Power running torque or output current
reached
f593
or more and maintain in
f595
during power running.

Enable  .

Reduce the load.

Check system error.
*

0049 Small-torque / Small
-current fault

Power running torque or output current
decreased f593 or less and maintain
in
f595
during power running.

Enable  .

Check system error.

0010 Overheat 
The cooling fan reaches the end of life or
has a fault.

The fan requires replacement if it does
not rotate during operation.
Contact your Toshiba distributor.

The ambient temperature is too high or
low against the specified ambient
temperature.

Operate at a specified ambient
temperature

The vent is blocked up.

Secure sufficient space around the inverter.

A heat generating device is installed close
to the inverter.

Do not place any heat generating device
near the inverter.


The load is large.

Reduce the load.

Reduce
f300
: PWM carrier frequency.

Set
f136
= 1 (Carrier frequency with
automatic reduction)


The temperature sensor has a fault.
(When the trip arises, as soon as it is
reset after a while.)

Contact your Toshiba distributor.

002E
Thermal fault stop
command from
external device

A thermal trip command (input terminal
function:  or  ) is issued by an
external control device.

The motor is overheated, so check
whether the current flowing into the motor
exceeds the rated current.

0011 Emergency stop 
During automatic operation or remote
operation, an emergency stop command
is entered from the operation panel or an
external (terminal or communication) .

Reset the inverter.

If the emergency stop signal is input,
reset after releasing this signal.

0012 EEPROM fault 1 
The EEPROM writing error occurs.

Turn off the inverter, then, turn it again.
If it does not recover from the error,
contact your Toshiba distributor.

0013 EEPROM fault 2 

operation is aborted by the power-
off etc.

Turn off the inverter, then, turn it again,
and then try

operation again.

The EEPROM reading error occurs.

Turn off the inverter, then, turn it again.
If it does not recover from the error,
contact your Toshiba distributor.

0014 EEPROM fault 3 
The EEPROM is defective.

Contact your Toshiba distributor.

0015 Main unit RAM fault 
The control RAM is defective.

Contact your Toshiba distributor.

0016 Main unit ROM fault 
The control ROM is defective.

Contact your Toshiba distributor.

0017 CPU fault 1 
The control CPU is defective.

Contact your Toshiba distributor.

0018 Communication error 
The communication with external devices
is broken off.

Check the remote control device, cables,
etc.

001A Current detector fault 
The current detector is defective.

Contact your Toshiba distributor.

001B Optional unit fault 1 
An optional unit has failed.
(such as a communication option)

Check the connection of optional unit.

001C Remote keypad
disconnection fault 
After run signal is activated by RUN key
of the remote keypad, disconnection is
occurred in 10 seconds or more.

In case the remote keypad is
disconnected, press STOP key before.

This fault is disabled by f731 = 1
setting.
* This marking trips can be selected valid or invalid by parameters.