Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 369

Страница: 369 / 427

GL-10x0 Administrator’s Guide

347

Cannot Acquire Document

Problem Description:

Cannot acquire a document using the GL-TWAIN driver.

Corrective Action:

The GL-TWAIN driver is carefully tested with several TWAIN-compliant

applications. Some applications need to be configured to connect to the

GL-TWAIN driver. See the scan

Readme

file for supported applications and

configuration tips.

B/W Image Reversed

Problem Description:

Image is acquired but the black and white areas of the image are

reversed.

Corrective Action:

Some applications may handle black and white pixilation incorrectly.

Enable the

Reverse Image

option from the application and try again.

Cannot Acquire Multi-Page Document

Problem Description:

Cannot acquire a multipage document from an application.

Corrective Action:

Some applications do not support multipage scan from TWAIN I/F, or

need to be configured to acquire multipage documents. See the

Readme

file on the Client CD-ROM.

Cannot Open a Password Protected Folder or Document

Problem Description:

A folder or document is password protected and you do not know which

password to apply.

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 369 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: