Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 327

Страница: 327 / 427

GL-10x0 Administrator’s Guide

305

Troubleshooting Checklist

Cannot Ping Controller

Possible Cause

Check

Yes

For Instructions,

Go To...

Networking
(protocol)
limitations or errors

1 Confirm that the TCP/IP

protocol suite is installed on the
client workstation.

Next
Step

The networking
section of your
operating system
documentation.

2 Look at the startup page and

confirm the TCP/IP settings are
correct. Is the IP Address
entered and valid? Are the
Gateway and Subnet settings
correct?

Next
Step

Enter the correct
TCP/IP settings.
Refer to

Configuring TCP/

IP Protocol

Settings

page 28.

3 Reboot the controller from the

LCD touch screen. Do

not

physically power down the
controller. Once the controller
comes back online, check the
startup page that prints out. Are
the TCP/IP settings correct?

Next
Step

The settings are not
binding, which could
indicate a NIC
installation issue.
Contact your
TOSHIBA authorized
dealer for support.

4 Try to ping the controller again.

Did the controller respond to the
ping?

End

Next
Step

Different and
unreachable
network segment

5 Can you ping the controller from

any other workstation within the
same network? If not, the
controller may be assigned an
IP Address that is out of range
or invalid.

Next
Step

Please contact your
local network
specialist for a valid
IP Address for the
controller.

6 Can you ping to another

workstation within the same
network?

Next
Step

Check the
workstation protocol
settings to make sure
the Gateway and
Subnet settings are
correct.

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 327 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: