Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 196

Страница: 196 / 427

174

GL-10x0

Administrator’s Guide

Peer to Peer Printing

Considerations and Limitations

You cannot assign the controller to a Microsoft domain; it can

participate only in a Microsoft workgroup.

The controller device name must be unique within the network. The

device name is also required in order to update the controller software

using TopAccess.

Prerequisites

Determine a unique device name (also known as the

host name

Microsoft

computer

name) for the controller. By default, the device

name is

GL<MAC Address>

, where

<MAC Address>

is the media

access control (MAC) number of the NIC installed in the controller.

You can change the device name, providing it is unique within the

network.

Pick a workgroup name for the device or accept the default name,

WORKGROUP

Configuring Microsoft Peer to Peer Printing

Launch your web browser. Open TopAccess using the IP address of

the controller you want to configure. (Refer to

Opening TopAccess

page 72.)

Note: You can find the IP address through TopAccessDocMon.

Click the Administration tab.

Click the Setup submenu.

Click the

Print Services

link.

In the Microsoft Printing area, make sure Microsoft printing is

Enabled

(default).

Select

Disable access to GL_PCL6

Disable access to GL_PS2

, or

Disable access to

dssc

to disable access to these print devices.

Scroll down to the bottom of the page and click

Save

Proceed to

Installing Client Software

on page 229.

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 196 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: