Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 143

Страница: 143 / 427

GL-10x0

Administrator’s Guide

121

On the Administration tab, click the

Setup

subtab. The Setup page

opens.

Click the

Wireless Network

link. The Wireless Network page opens.

In the DDNS area, click the down arrow beside the

Update DNS

Dynamically

pull-down list box.

Select

Enable

to enable DDNS or

Disable

to disable DDNS.

Enter the host name of the DNS server in the

Host Name

field. This field

is disabled if DDNS is disabled. The default value for this field is the

MAC address of the controller.

Scroll down to the bottom of the page and click

Save

to save your

settings.
Alternatively, click

Reset

to reset all settings on this page to the default

values.

Reboot the controller for the changes to take effect.

Configuring SMB Settings

If you are using the SMB networking protocol for any wireless network

traffic involving the controller, you must enable the SMB protocol on the

wireless NIC. The SMB protocol is enabled by default. If you are not using

SMB for any wireless network traffic, disabling the SMB protocol on the

wireless NIC reduces overhead and improves efficiency.
1

On the Administration tab, click the

Setup

subtab.

Click the

Wireless Network

link. The Wireless Network page opens.

In the SMB area of the Wireless Network page, click the

Protocol

drop-

down list.

Select

Enable

to enable the SMB protocol.

In the

Device Name

field, enter the controller name.

Enter the name of the

Workgroup

the controller belongs to.

Enter the address of the

Primary WINS Server

Enter a

WINS Scope ID

for the controller.

10 To set the controller as a master browser, click the

Master Browser

drop-

down list and select

Enable

11 Click

Save

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 143 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: