manualshive.com logo in svg

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 328 / 427

Поделиться
Скачать
Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 328

306

 GL-10x0 Administrator’s Guide

Cannot Print from Client

Problem Description

After following the instructions in this guide to install and configure your 

hardware, network, and client software, you are still unable to print from 

a client workstation to your TOSHIBA Network Document Processing 

System. This problem can arise as the result of a hardware malfunction, a 

network communication or configuration problem, or incorrect client 

setup or driver properties.
The following checklist helps you identify the source of the error and 

directs you to where you can find more information about resolving it. If 

the problem persists after you have followed all of the steps, contact your 

TOSHIBA authorized dealer for further assistance.

NIC or hardware 
failure.

7 If you have customized the 

device name, you can check if 
the NIC is functional by 
restoring the controller default 
settings from the copier control 
panel. When the controller 
automatically reboots and a 
startup page prints, does the 
device name include the NIC 
MAC address? 

Next 
Step

’

‘

The NIC is faulty or 
improperly installed. 
Contact your 
TOSHIBA authorized 
dealer for support.

8 Check link activities on the port 

being used by the controller and 
the integrity of the network 
cable, hub, or switch that 
connects the controller to the 
network. Replace any network 
components that you can tell or 
suspect are faulty. Can you ping 
the controller now?

End

‘

Contact your 
TOSHIBA authorized 
dealer for support.

Cannot Ping Controller (Continued)

Possible Cause

Check

Yes

No

For Instructions, 

Go To...

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Отзывы:

Нет отзывов