Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 334

Страница: 334 / 427

312

GL-10x0 Administrator’s Guide

Common Errors

Startup Page Does Not Print

Problem Description

If a startup page does not print when you power on the copier, this

indicates there is a problem either with copier operation or with

communications between the copier and the controller. However, if the

startup page does print but all the values are

none

, this could indicate

that someone pressed the

RESTORE DEFAULTS

key. Reboot the controller.

If the values are still

none

, contact your TOSHIBA authorized dealer for

support.
The following checklist helps you identify the source of the error and

directs you to where you can find more information about resolving it. If

the problem persists after you have followed all of the steps, contact your

TOSHIBA authorized dealer for further assistance.

Troubleshooting Checklist

Starting Controller, Please Wait

Shut-down

in Progress, Please Wait

Message Appears

Problem Description

The first response many users have to seeing this error message displayed

on the copier LCD touch screen is to restart the controller. However,

doing so can corrupt the controller software or hard disk. Often, the

message simply indicates unsynchronized communication between the

copier and the controller, which is easy to resolve. Other times, the

message results from damaged hardware or corrupt software.

Startup Page Does Not Print

Possible Cause

Check

Yes

For Instructions,

Go To...

Miscommunication
between the copier
and the controller

1 Check the copier LCD touch

screen. Press

PRINTER/

NETWORK

. Does the print/

admin panel appear?

End

Call

Reboot the controller
to restore
communication.
Refer to

Rebooting

the Controller

page 43.

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 334 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: