Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 169

Страница: 169 / 427

GL-10x0

Administrator’s Guide

147

By default, all network protocols are enabled.
You must be logged in as an administrator to set wireless network

protocol properties.

Enabling/Disabling the Wireless Card

On the Administration tab, click the

Setup

subtab.

Click the

Wireless Network

link. The Wireless Network page opens.

Wireless Page

In the Device area, click the

Wireless Card

drop-down list.

Select

Enable

Disable

Click

Save

Configuring IPX/SPX Settings

On the Administration tab, click the

Setup

subtab.

Click the

Wireless Network

link. The Wireless Network page opens.

In the IPX/SPX area, click the

Protocol

drop-down list.

Select

Enable

to enable IPX/SPX.

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 169 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: