Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 325 | Manualshive

Страница: 325 / 427

Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 325

GL-10x0 Administrator’s Guide

303

The following checklist helps you identify the source of the error and

directs you to where you can find more information about resolving it. If

the problem persists after you have followed all of the steps, contact a

TOSHIBA authorized dealer for further assistance.

Troubleshooting Checklist

Device Discovery

Possible Cause

Check

Yes

No

For Instructions,

Go To...

Networking
(protocol)
limitations or errors

1 Confirm that the protocol

suite installed on the client
workstation has been
updated with the latest
software for the given
operating system. If your
network only supports the
IPX/SPX protocol, make sure
that the most current version
of Novell Client software is
installed.

Next
Step

See the vendor’s Web
site for information
about product updates
and technical support.

2 Print a startup page from the

copier. Does the controller
support the same protocol as
the network?

Next
Step

Modifying

Controller Settings

at the Control

Panel

on page 21.

3 Change the protocol settings

from the copier control panel,
if necessary, and reboot the
controller for the changes to
take effect. Repeat Step 2.
Was the device discovered?

End

Next
Step

Modifying

Controller Settings

at the Control

Panel

on page 21.

Unreachable
network segment

4 Check the controller startup

page. Are the IP Address
and subnet mask settings
correct?

Next
Step

Modifying

Controller Settings

at the Control

Panel

on page 21.

5 Check the router to make

sure it is not filtering out the
controller packets. Is the
router processing packets
correctly?

Next
Step

Adjust the router
settings.

«
...
323
324
325
326
327
...
»

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Отзывы:

Нет отзывов