Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 139

Страница: 139 / 427

GL-10x0

Administrator’s Guide

117

Configuring SMB Settings

If you are using the SMB networking protocol for any network traffic

involving the controller, you must enable the SMB protocol on the

controller. The SMB protocol is disabled by default. If you are not using

SMB for any network traffic, disabling the SMB protocol on the controller

reduces overhead and improves efficiency.
1

In the SMB area of the Network page, click the

Protocol

drop-down list.

Select

Enable

to enable SMB protocol. This is the default setting.

In the

Device Name

field, enter the controller name.

Enter the controller

Workgroup

in the appropriate field.

Enter the address of the

Primary WINS Server

Enter a

WINS Scope ID

for the controller.

Note: Macintosh and Unix networks must have WINS or NETBIOS

support to access the GL-1020 controller by name instead of IP

address.

To set the controller as a master browser, click the

Master Browser

drop-

down list and select

Enable

. The default setting is

Disable

Click

Save

10 If you change the TCP/IP protocol settings or enable/disable a

network card, you must reboot the controller before the changes take

effect.
For information on rebooting the controller, see

Rebooting the

Controller

on page 43.

Configuring AppleTalk Settings

If you are using the AppleTalk networking protocol for any network traffic

involving the controller, you must enable the AppleTalk protocol on the

controller. The AppleTalk protocol is enabled by default. If you are not

using AppleTalk for any network traffic, disabling the AppleTalk protocol

on the controller reduces overhead and improves efficiency.
1

On the Administration tab, click the

Setup

subtab.

Click the

Network

link. The Network page opens.

In the AppleTalk area, click the

Protocol

drop-down list.

Select

Enable

to enable AppleTalk. This is the default setting.

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 139 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: