Toshiba e-STUDIO GL-1010 Скачать руководство пользователя страница 330

Страница: 330 / 427

308

GL-10x0 Administrator’s Guide

Job Not Listed in Current Jobs

Problem Description

If a job submitted to the controller does not appear in the current jobs

queue, visible from TopAccess, TopAccessDocMon, or the copier control

panel the most likely causes are a network issue or a client software

installation and configuration error.
The following checklist helps you identify the source of the error and

directs you to where you can find more information about resolving it. If

the problem persists after you have followed all of the steps, contact your

TOSHIBA authorized dealer for further assistance.

Troubleshooting Checklist

The client is not
communicating with
the controller

6 Open TopAccessDocMon

and note the taskbar
connection icon and status
bar message. Is the
controller responding?

Next
Step

TopAccessDocMon

Status: The

Controller is not

responding

page 337.

The controller was
unable to process the
job request

7 Try resubmitting the job.

Does the printer status read

Document has printed
successfully

End

Cannot Interpret

TopAccessDocMon

Messages/

Warnings/Errors

on page 340.

Client Error (Mac Platform)

The TOSHIBA PPD
file is not installed
properly

8 Is the printer you created

selected in the Chooser
(OS9.2.2+) or the Print
Center (OS10.2.6+)?

End

Installing

Macintosh PPD

Files

on page 234.

Submitted Job Not in Current Jobs Queue

Possible Cause

Check

Yes

For Instructions,

Go To...

Software Error

Cannot Print From Client

Possible Cause

Check

Yes

For Instructions,

Go To...

Содержание e-STUDIO GL-1010












































































































































































































































































































































































































































Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы:

Toshiba e-STUDIO GL-1010, Руководство администратора, Страница: 330 / 427

Результаты поиска

Содержание e-STUDIO GL-1010

Отзывы: