manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

IMPORTANT

WARNING/CAUTION/NOTE

Please read this manual and follow its instructions
carefully. To emphasize special information, the words
WARNING, CAUTION and NOTE have special mean-
ings. Pay special attention to the messages high-
lighted by these signal words.

WARNING:
Indicates a potential hazard that could result
in death or injury.

CAUTION:
Indicates a potential hazard that could result
in vehicle damage.

NOTE:
Indicates special information to make mainte-
nance easier or instructions clearer.

WARNING:
This service manual is intended for autho-
rized Suzuki dealers and qualified service
mechanics only. Inexperienced mechanics
or mechanics without the proper tools and
equipment may not be able to properly per-
form the services described in this manual.
Improper repair may result in injury to the
mechanic and may render the vehicle un-
safe for the driver and passengers.

WARNING:
For vehicles equipped with a Supplemental
Restraint Air Bag System:

Service on and around the air bag system
components or wiring must be performed
only by an authorized SUZUKI dealer.
Please observe all WARNINGS and CAU-
TIONS in SECTION 10B and Precautions,
Air Bag System Components and Wiring
Location View in SECTION 10B or before
performing service on or around the air
bag system components or wiring. Failure
to follow WARNINGS could result in
unintentional activation of the system or
could render the system inoperative. Ei-
ther of these two conditions may result in
severe injury.

If the air bag system and another vehicle
system both need repair, Suzuki recom-
mends that the air bag system be repaired
first, to help avoid unintended air bag de-
ployment.

Do not modify the steering wheel, instru-
ment panel or any other air bag system
component (on or around air bag system
components or wiring). Modifications can
adversely affect air bag system perfor-
mance and lead to injury.

If the vehicle will be exposed to tempera-
tures over 93

C (200

F) (for example, dur-

ing a paint baking process), remove the
air bag system components (air bag (infla-
tor) modules, SDM and/or seatbelt with
pretensioner) beforehand to avoid com-
ponent damage or unintended deploy-
ment.

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Lancia Delta Owner'S Handbook Manual preview
Delta
Бренд: Lancia Страницы: 276
T-Tech TT100 User Manual preview
TT100
Бренд: T-Tech Страницы: 38
Laser 4832 Manual preview
4832
Бренд: Laser Страницы: 8
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Бренд: Subaru Страницы: 34
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Бренд: Wagan Страницы: 20
Whispbar K448W Fitting Instructions Manual preview
K448W
Бренд: Whispbar Страницы: 15
AddSecure Asset Light Installation Manual preview
Asset Light
Бренд: AddSecure Страницы: 14
P-Invent Troller User Manual preview
Troller
Бренд: P-Invent Страницы: 4
Quadratec 12057.0263 Installation Manual preview
12057.0263
Бренд: Quadratec Страницы: 12
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Бренд: ULTIMATE SPEED Страницы: 40
Calix group TYP MVP 823 Assembly Instructions preview
TYP MVP 823
Бренд: Calix group Страницы: 4
Honda CRV 2015 Navigation Manual preview
CRV 2015
Бренд: Honda Страницы: 253
Toyota 2018 yaris Vehicle Instruction Card preview
2018 yaris
Бренд: Toyota Страницы: 11
Mitsubishi 3000gt 1999 Workshop Manual preview
3000gt 1999
Бренд: Mitsubishi Страницы: 57
ULTIMATE SPEED 1188 1525 Instructions For Use And Safety Manuallines preview
1188 1525
Бренд: ULTIMATE SPEED Страницы: 26
Car-Interface CI-RL4-R40 Manual preview
CI-RL4-R40
Бренд: Car-Interface Страницы: 25
Arctic Cat 2010 ATV 150 Service Manual preview
2010 ATV 150
Бренд: Arctic Cat Страницы: 101
RAWLINK 36772 Instruction Manual preview
36772
Бренд: RAWLINK Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды