MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 75

Страница: 75 / 324

2-57

BEFORE DRIVING

68PH0-74E

sumption is 50. No more than 50 will be

indicated on the display even if the

actual instantaneous fuel consumption is

higher.

• The indication on the display may be

delayed if fuel consumption is greatly

affected by driving conditions.

• The display shows estimated values.

Indications may not be the same as

actual values.

• You can change the units that instanta-

neous fuel consumption is displayed in.

Refer to “Average fuel consumption” in

this section.

Average fuel consumption

If you selected average fuel consumption

the last time you drove the vehicle, the dis-

play shows the last value of average fuel

consumption from previous driving when

the ignition switch is turned to the “ON”

position. Unless you reset the value of

average fuel consumption, the display indi-

cates the value of average fuel consump-

tion which includes average fuel

consumption during previous driving.
To reset the average fuel consumption to

zero, push and hold the indicator selector

knob (2) for a while when the display

shows the average fuel consumption.

NOTE:

When you reset the indication or reconnect

the negative (–) terminal to the battery, the

value of average fuel consumption will be

shown after driving for a while.

To change the unit of average fuel con-

sumption, while pushing and holding the

trip meter selector knob (1), turn the indica-

tor selector knob (2).

68PH02207

NOTE:

• When you change the units that average

fuel consumption is displayed in, the

instantaneous fuel consumption units will

be changed automatically.

• When you reconnect the negative (–)

terminal to the battery, the unit of the

average fuel consumption will be reini-

tialized. Change the unit again to your

preference.

Driving range

If you selected driving range the last time

you drove the vehicle, the display indicates

“

---

” for a few seconds and then indicates

the current driving range when the ignition

switch is turned to the “ON” position.
The driving range shown in the display is

the approximate distance you can drive

until the fuel gauge indicates “E”, based on

current driving conditions.
When the low fuel warning light comes on,

the display “---” will appear.
If the low fuel warning light comes on, fill

the fuel tank immediately regardless of the

value of driving range shown in the display.
As the driving range after refueling is cal-

culated based on the most recent driving

condition, the value is different each time

you refuel.

NOTE:

• If you refuel when the ignition switch is in

the “ON” position, the driving range may

not indicate the correct value.

• When you reconnect the negative (–)

terminal to the battery, the value of driv-

ing range will be shown after driving for a

while.

Gearshift Indicator

Refer to “Gearshift Indicator” in the

“OPERATING YOUR VEHICLE” section.

EXAMPLE

(Initial
setting)

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды