MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 127

Страница: 127 / 324

2-109

BEFORE DRIVING

68PH0-74E

Rear Window Wiper/Washer Switch

(If equipped)

68PH00263

To turn the rear wiper on, twist the rear

wiper switch on the end of the lever for-

ward to the “ON” position. To turn the rear

wiper off, twist the switch rearward to the

“OFF” position.
With the rear wiper in the “OFF” position,

twist the switch rearward and hold it there

to spray window washer fluid.
With the rear wiper in the “ON” position,

turn the switch forward and hold it there to

spray window washer fluid.

Tilt/Telescoping (If equipped)
Steering Lock Lever

68PH00264

(1) LOCK

(2) UNLOCK

The lock lever is located under the steering

column. To adjust the steering wheel

height and fore-aft position:
1) Push down the lock lever to unlock the

steering column.

2) Adjust the steering wheel to the desired

height and fore-aft position and lock the

steering column by pulling the lock

lever.

3) Try moving the steering wheel up and

down and back and forth to make sure

it is securely locked in position.

Washer

Wiper

EXAMPLE

NOTICE

Clear ice or snow from the rear win-

dow and rear wiper blade before

using the rear wiper. Accumulated

ice or snow could prevent the wiper

blade from moving, causing damage

to the wiper motor.

(1)

(2)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды