MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 143

Страница: 143 / 324

3-13

OPERATING YOUR VEHICLE

68PH0-74E

help you. Refer to “Information Display”

in the “BEFORE DRIVING” section for

details.

• You should turn off such loads as the

headlights and air conditioning system to

facilitate starting of the engine.

• Even if you fail to start the engine, the

starter motor will stop turning automati-

cally after a short time. After the starter

motor has stopped or if there is some

problem with the system, the starter

motor will rotate only while the engine

switch is being pressed.

Stopping the engine

• Depress the engine switch to stop the

engine after the vehicle stopped com-

pletely.

• In case of emergency, you can stop the

engine by quickly pushing the engine

switch more than 3 times, or pushing

and holding the engine switch more than

2 seconds while the vehicle in motion.

NOTE:

Except in emergency, do not stop the

engine while the vehicle is in motion.

The steering and braking operation will

require more efforts when the engine is

stopped.

Refer to “Braking” in this section.

• If the vehicle is stopped & stays as it is

for while after the engine was stopped

unexpectedly or was raced before stop-

ping, a clicking sound may be heard

from around the engine when the engine

is restarted. This is not a malfunction. In

such cases, always let the engine idle

before stopping it.

Starting a Cold and Warm Engine

(For petrol engine model)

With your foot off the accelerator pedal,

crank the engine by pressing the engine

switch to change the ignition mode to

“START”.

After pressing the engine switch to change

the ignition mode to “START”, the starter

cranks the engine for about 12 seconds

before it can start the engine. If the engine

fails to start at the first attempt, wait about

15 seconds, then try again while keeping

the engine switch pressed while pressing

down the accelerator pedal to 1/3 of its

travel. Release the accelerator pedal when

the engine starts.
If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

If you are unable to start the engine using

this procedure, consult your authorised

Maruti Suzuki workshop.

(For diesel engine model)

Cold engine

Depress the clutch and brake pedals fully

and press the engine switch to crank the

engine. If the glow plug indicator light

comes on, the engine will start automati-

cally after the glow plug indicator light goes

off or 10 seconds pass.

Warm engine

Crank the engine by pressing the engine

switch to change the ignition mode to

“START”.

Caution when stopping the engine with

turbocharger

When stopping the engine after climbing or

high speed driving, let the engine idle for

about one minute or more (If it is not pro-

hibited) to cool down the turbocharger and

engine oil. This is to prevent the engine oil

from over-deteriorating. Deteriorated

engine oil will damage the bearings of the

turbocharger.

NOTICE

Do not crank the engine for more

than 12 seconds at a time.

If the engine doesn’t start on the first

try, wait about 15 seconds before try-

ing again.

NOTICE

Do not crank the engine for more

than 30 seconds at a time.

If the engine doesn’t start on the first

try, wait about 15 seconds before try-

ing again.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды