MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 174

Страница: 174 / 324

5-2

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Engine Hood

68PH00503

To open the engine hood:

1) Pull the hood release handle located on

the outboard side of the driver’s side of

the instrument panel. This will disen-

gage the engine hood lock halfway.

68PM05002

2) Push the under-hood release lever

sideways with your finger, as shown in

the illustration. While pushing the lever,

lift up the engine hood.

WARNING

If you need to replace the fuel cap,

use a MARUTI genuine cap. Use of an

improper cap can result in a malfunc-

tion of the fuel system or emission

control system. It may also result in

fuel leakage in the event of an acci-

dent.

EXAMPLE

CAUTION

The release lever can be hot enough

to burn your finger right after driving.

Touch the lever after it becomes cool

enough.

NOTICE

Make sure that the wiper arms are not

raised before you lift up the engine

hood to avoid damaging the wiper

arms and the engine hood.

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды