MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 185

Страница: 185 / 324

5-13

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Front Seat Back Pocket

(If equipped) (6)

68PH00528

This pocket is provided for holding light

and soft things such as gloves, newspa-

pers or magazines.

Footrest

68PH00529

Use the footrest (1) as a support for your

left foot.

Floor Mats (If equipped)

68PH00530

To prevent the driver’s side floor mat from

sliding forward and possibly interfering with

the operation of the pedals, MARUTI genu-

ine floor mats are recommended.

Whenever you put the driver’s side floor

mat back in the vehicle after it has been

removed, be sure to hook the floor mat

grommets to the fasteners and position the

floor mat properly in the footwell.
When you replace the floor mats in your

vehicle with a different type such as all-

weather floor mats, we highly recommend

using MARUTI genuine floor mats for

proper fitting.

CAUTION

Do not put sharp-edged hard or

breakable objects in the pocket. If an

accident occurs, objects such as bot-

tles, cans, etc. can injure the occu-

pants in the rear seat.

EXAMPLE

(1)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды