MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 103

Страница: 103 / 324

2-85

BEFORE DRIVING

68PH0-74E

Warning and indicator messages
All model

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound

Cause and remedy

68PH02232

Blinks

(Only while vehi-

cle is in motion)

Beep (One time from interior

buzzer; only while vehicle is

in motion)

A door or tailgate is not properly closed.

Stop the vehicle in a safe place and close

the door or tailgate properly. (#1)

68PH02233

Blinks

Continuous beep (From inte-

rior buzzer)

The headlights and/or the position lights are

left on. Turn them off.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды