MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 54

Страница: 54 / 324

2-36

BEFORE DRIVING

68PH0-74E

Infant restraint - rear seat only

80JC007

Child restraint

80JC016

Booster seat

80JC008

MARUTI SUZUKI highly recommends that

you use a child restraint system to restrain

infants and small children. Many different

types of child restraint systems are avail-

able; make sure that the restraint system

you select meets applicable safety stan-

dards.
All child restraint systems are designed to

be secured on vehicle seats by seat belts

(Lap belts or the lap portion of lap-shoulder

belts). Whenever possible, MARUTI

SUZUKI recommends that child restraint

systems be installed on the rear seat.

According to accident statistics, children

are safer when properly restrained in rear

seating positions than in front seating posi-

tions.

If you must use a front-facing child

restraint in the front passenger’s seat,

adjust the passenger’s seat as far back as

possible.

NOTE:

Observe any statutory regulation about

child restraints.

58MS030

EXAMPLE

WARNING

Do not install a rear-facing child

restraint in the front passenger’s

seat. If the passenger’s air bag

inflates, a child in a rearfacing child

restraint could be killed or seriously

injured. The back of a rear-facing

child restraint would be too close to

the inflating air bag.

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды