MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 65

Страница: 65 / 324

2-47

BEFORE DRIVING

68PH0-74E

Therefore, an air bag is NOT a substitute

for seat belts. To maximize your protection,

ALWAYS WEAR YOUR SEAT BELTS. Be

aware that no system can prevent all pos-

sible injuries that may occur in an accident.

Driver’s front air bag

68PH00248

Front passenger’s front air bag

68PH00249

The driver’s front air bag is located behind

the center pad of the steering wheel and

the front passenger’s front air bag is

located behind the passenger’s side of the

dashboard.

The words “SRS AIRBAG” are molded into

the air bag covers to identify the location of

the air bags.

58MS030

Please refer to the “Seat Belts and Child

Restraint Systems” section in this section

for details on securing your child.

EXAMPLE

WARNING

Do not install a rear-facing child

restraint in the front passenger’s

seat. If the passenger’s front air bag

inflates, a child in a rear-facing child

restraint could be killed or severely

injured. The back of a rear-facing

child restraint would be too close to

the inflating air bag.

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды