MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 288

Страница: 288 / 324

7-32

INSPECTION AND MAINTENANCE

68PH0-74E

Front turn signal light and

front position light

Vehicle with the halogen headlights

68PH00730

(1) Front turn signal light

(2) Front position light

Vehicle with the discharge headlights

68PH00731

(1) Front turn signal light

68PH00732

1) Open the engine hood. To remove the

bulb holder of the front turn signal light

or the front position light from the light

housing, turn the holder counterclock-

wise and pull it out.

68PH00733

(3) Removal

(4) Installation

2) To remove the bulb of the front turn sig-

nal light (1) from the bulb holder, push

in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn

it clockwise.

To remove and install the bulb of the

front position light (2), simply pull out or

push in the bulb.

(1)

(2)

EXAMPLE

(1)

EXAMPLE

(1)

(2)

(3)

(4)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды