MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 289

Страница: 289 / 324

7-33

INSPECTION AND MAINTENANCE

68PH0-74E

Front Fog Light (If equipped)

1) Start the engine. Turn the steering

wheel to the opposite side of the replac-

ing fog light to replace the bulb easily.

Then turn off the engine.

68PM07002

2) Remove the clips (1).

68PM07003

3) Open the end of the cover inside the

fender.

68PH00736

4) Disconnect the coupler by pushing the

lock release. Turn the bulb holder coun-

terclockwise and remove it.

Rear combination light

68PH00737

1) Remove the bolts (1) and pull the light

housing (2) straight.

68PH00738

2) Remove the wire (3) from a clamp (4).

(1)

EXAMPLE

(1)

(2)

EXAMPLE

(4)

(3)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды