MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 145

Страница: 145 / 324

3-15

OPERATING YOUR VEHICLE

68PH0-74E

less push start system remote controller

cannot be used to lock them.)

• Disconnect the negative cable from the

battery to prevent discharge.

“LOCK” (OFF) mode reminder buzzer

If the driver’s door is opened without

returning the ignition mode to “LOCK”

(OFF) by pressing the engine switch, a

buzzer sounds to warn you of this state.
• If you open the driver’s door after press-

ing the engine switch to change the igni-

tion mode to “ACC”, the interior buzzer

beeps intermittently.

• The buzzer will stop sounding if you then

push the engine switch twice, thus bring-

ing it back the ignition mode to “LOCK”

(OFF).

NOTE:

Whenever you leave the vehicle, make

sure you have returned the ignition mode

to “LOCK” (OFF) using the engine switch

and then lock the doors. Without returning

the ignition mode to “LOCK” (OFF), you

cannot use a request switch or keyless

push start system remote controller to lock

the doors.

Steering lock warning buzzer

If the steering lock fails to engage due to a

fault in the system when the ignition mode

is turned to “LOCK” (OFF) by pressing the

engine switch and then any door (including

the tailgate) is opened or closed, the inte-

rior buzzer will warn you of this condition

with repeated short beeps. If this happens,

have the vehicle inspected by an autho-

rised Maruti Suzuki workshop.

Using the Transaxle

Manual Transaxle

79MH0303

Starting off

To start off, depress the clutch pedal all the

way to the floor and shift into 1st gear.

After releasing the parking brake, gradually

release the clutch. When you hear a

change in the engine’s sound, slowly press

the accelerator while continuing to gradu-

ally release the clutch.

Shifting

All forward gears are synchronized, which

provides for quiet, and easy shifting.

Always depress the clutch pedal all the

way to the floor before shifting gears. Keep

the engine speed to a value so that it does

not rise into the red zone of the tachome-

ter.

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды