MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 166

Страница: 166 / 324

4-4

DRIVING TIPS

68PH0-74E

• When driving down a hill, the engine

should be used for braking by shifting to

next lower gear. (Do this with either a

CVT or a manual transaxle vehicle).

While moving uphill/gradient from a

stand still condition

• Apply the parking brake firmly so that the

vehicle does not roll backwards.

• Depress the Clutch pedal and Shift the

gearshift lever to 1

Select position.

• Do not slip the clutch.

• When ready to start, press accelerator

pedal and slowly release the clutch

pedal simultaneously. When the vehicle

starts to move, gradually release the

parking brake.

Driving on Slippery Roads

60G089S

Under wet road conditions you should

drive at a lower speed than on dry roads

due to possible slippage of tires during

braking. When driving on icy, snow-cov-

ered, or muddy roads, reduce your speed

and avoid sudden acceleration, abrupt

braking, or sharp steering movements.

Tire Chains

Tire chains should only be used if they are

needed to increase traction or are required

by law. Make sure that the chains you use

are the correct size for your vehicle’s tires.

Also make sure that there is enough clear-

ance between the fenders and the chains

as installed on the tires.
Install the chains on the front tires tightly,

according to the chain manufacturer’s

instructions. Retighten the chains after

driving about 1.0 km if necessary. With the

chains installed, drive slowly.

WARNING

Try not to hold the brake pedal down

too long or too often while going

down a steep or long hill. This could

cause the brakes to overheat, result-

ing in reduced braking efficiency.

Failure to take this precaution could

result in loss of vehicle control.

NOTICE

When descending down a hill,

NEVER turn the ignition key to the

“LOCK” position or press the engine

switch to change the ignition mode to

“LOCK” (OFF). Emission control sys-

tem and CVT (If equipped) damage

may result.

EXAMPLE

NOTICE

• If you hear the chains hitting

against the vehicle body while driv-

ing, stop and tighten them.

• If your vehicle is equipped with full

wheel caps, remove the wheel caps

before installing the chains or the

wheel caps can be damaged by the

chain bands.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды