MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 33

Страница: 33 / 324

2-15

BEFORE DRIVING

68PH0-74E

Security System (If equipped)

The security system is armed in about 5

seconds after you lock all doors (including

the tailgate) by using the keyless entry sys-

tem transmitter, keyless push start system

remote controller or request switch.

Once the system is armed, any attempt to

open a door by using any other means (*)

than the keyless entry system transmitter,

keyless push start system remote control-

ler or open the engine hood, will cause the

alarm to be triggered.

* These means include the following:

– The key

– The lock knob on a door

– The central door locking switch

– The tailgate emergency lever

Also, in case that you have set the shock

sensor to enabled state and set sensitivity

of the pre-warning function and full blast

warning function to a level other than 0, the

alarm will be triggered if any attempt to

tamper with the vehicle. The shock sensor

can be selected enabled or disabled state,

and sensitivity of each warning can be

adjusted as desired. To set the shock sen-

sor, ask your authorised Maruti Suzuki

workshop or use the setting mode of the

information display.

NOTE:

• The default setting of the shock sensor

is in the disabled state. Set to the

enabled state and adjust sensitivity of

each warning according to your prefer-

ence. For details on how to use the infor-

mation display, refer to “Information

Display” in this section.

• Your dealer may have already set the

shock sensor of the vehicle to the

enabled state before you purchase it.

Consult your dealer for further informa-

tion.

NOTE:

• The security system generates alarms

when any of the predetermined condi-

tions is met. However, the system does

not have any function of blocking unau-

thorized entry into the vehicle.

• Always use the keyless entry system

transmitter or keyless push start system

remote controller to unlock the doors when

the security system has been armed.

Using a key instead will trigger the alarm.

• If a person who does not know the secu-

rity system is going to drive the vehicle,

we recommend you explain the system

and its operation to the person, or dis-

able the system beforehand. Mistakenly

triggering the alarm may cause a nui-

sance to others.

• Even if the security system is armed,

you should still be careful to guard

against theft. Do not leave money or

things of value in the vehicle.

How to arm the security system

(When enabled)

Lock all doors (including the tailgate) using

the keyless entry system transmitter or

keyless push start system remote control-

ler. The security system indicator (1) will

start blinking rapidly, and the security sys-

tem will be armed in about 5 seconds.

While the system is being armed, the indi-

cator continues to blink at intervals of

approximately 2 seconds.

68PH00218

(1)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды