MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 141

Страница: 141 / 324

3-11

OPERATING YOUR VEHICLE

68PH0-74E

Starting the Engine
(Vehicle without keyless push
start system)

Before Starting the Engine

68PH00308

1) Make sure the parking brake is set fully.

2) Manual transaxle – Shift into “N” (Neu-

tral) and depress the clutch pedal all

the way to the floor. Hold the clutch

pedal while starting the engine.

CVT – If the gearshift lever is not in “P”

(Park) position, shift into “P” (Park). (If

you need to re-start the engine while

the vehicle is moving, shift into “N”.)

NOTE:

CVT vehicles have a starter interlock

device which is designed to keep the

starter from operating if the transaxle is in

any of the drive positions.

NOTE:

The engine of manual transaxle vehicle will

not start unless the clutch pedal is

depressed.

Starting a Cold and Warm Engine

(For petrol engine model)

With your foot off the accelerator pedal,

crank the engine by turning the ignition key

to “START”. Release the key when the

engine starts.

If the engine does not start after 12 sec-

onds of cranking, wait about 15 seconds,

then press down the accelerator pedal to

1/3 of its travel and try cranking the engine

again. Release the key and accelerator

pedal when the engine starts.

If the engine still does not start, try holding

the accelerator pedal all the way down to

the floor while cranking. This should clear

the engine if it is flooded.

(For diesel engine model)
Cold engine

Turn the ignition switch to the “ON” posi-

tion and wait until the glow plug indicator

goes out if it comes on. Crank the engine

by turning the ignition key to “START”.

Release the key when the engine starts.

EXAMPLE

WARNING

Make sure that the parking brake is

set fully and the transaxle is in Neu-

tral (or Park for vehicles with CVT)

before attempting to start the engine.

NOTICE

• Stop turning the starter immedi-

ately after the engine has started or

the starter system can be damaged.

• Do not crank the engine for more

than 12 seconds at a time. If the

engine doesn’t start on the first try,

wait about 15 seconds before try-

ing again.

NOTICE

• Stop turning the starter immedi-

ately after the engine has started or

the starter system can be damaged.

• Do not crank the engine for more

than 30 seconds at a time. If the

engine doesn’t start on the first try,

wait about 15 seconds before try-

ing again.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды