MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 267

Страница: 267 / 324

7-11

INSPECTION AND MAINTENANCE

68PH0-74E

Engine Coolant

Selection of Coolant

To maintain optimum performance and

durability of your engine, use MARUTI

Genuine Coolant or equivalent.
This type of coolant is best for your cooling

system as it:

• Helps maintain proper engine tempera-

ture.

• Gives proper protection against freezing

and boiling.

• Gives proper protection against corro-

sion and rust.

Failure to use the proper coolant can dam-

age your cooling system. Your authorised

Maruti Suzuki workshop can help you

select the proper coolant.

Coolant Level Check

Check the coolant level at the reservoir

tank, not at the radiator. With the engine

cool, the coolant level should be between

the “FULL” and “LOW” marks.

NOTICE

• When replacing the oil filter, it is

recommended that you use a MAR-

UTI genuine replacement filter. If

you use an aftermarket filter, make

sure it is of equivalent quality and

follow the manufacturer’s instruc-

tions.

• Oil leaks from around the oil filter

or drain plug indicate incorrect

installation or gasket damage. If

you find any leaks or are not sure

that the filter has been properly

tightened, have the vehicle

inspected by your authorised

Maruti Suzuki workshop.

NOTICE

To avoid damaging your cooling sys-

tem:

• Always use a high quality ethylene

glycol base non-silicate type cool-

ant diluted with distilled water at

the correct mixture concentration.

• Make sure that the proper mix is 50/

50 coolant to distilled water (Die-

sel) and 30/70 (Petrol) and in no

case higher than 70/30. Concentra-

tions greater than 70/30 coolant to

distilled water will cause overheat-

ing conditions.

• Neither use 100% coolant nor 100%

plain water.

• Do not add extra inhibitors or addi-

tives. They may not be compatible

with your cooling system.

• Do not mix different types of base

coolants. Doing so may result in

accelerated seal wear and/or the

possibility of severe overheating

and extensive engine/CVT damage.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды