MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 269

Страница: 269 / 324

7-13

INSPECTION AND MAINTENANCE

68PH0-74E

If the coolant level is below the “LOW”

mark, more coolant should be added.

When the engine is cool, remove the

degassing tank cap by turning it anticlock-

wise slowly to release any pressure. And

add coolant until the degassing tank level

reaches the “FULL” mark. Never fill the

degassing tank above the “FULL” mark.

Coolant Replacement

Since special procedures are required, we

recommend you take your vehicle to your

authorised Maruti Suzuki workshop for

coolant replacement.

Air Cleaner

If the air cleaner is clogged with dust, there

will be greater intake resistance, resulting

in decreased power output and increased

fuel consumption.

(For petrol engine model)

K10C model

68PM00734

1) Remove the bolts (1) and lift the air

cleaner case (2) directly above.

68PM00705

2) Unclamp the side clamps and remove

the element from the air cleaner case. If

the element appears to be dirty clean

the element or replace it with a new one

as per periodic maintenance schedule.

3) Clamp the side clamps securely.

(1)

(2)

(1)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды