MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 133

Страница: 133 / 324

3-3

OPERATING YOUR VEHICLE

68PH0-74E

You should also be aware that the diluting

ingredients evaporate out when the vehicle

is subsequently driven at high speeds,

such as on an expressway, making it

appear that oil is excessively consumed

after high-speed driving.

Ignition Switch
(Vehicle without keyless push
start system)

65D611

68PH00310

The ignition switch has the following four

positions:

LOCK

This is the normal parking position. It is the

only position in which the key can be

removed.

Manual transaxle

68PH00301

• Manual transaxle vehicles

You must push in the key to turn it to the

“LOCK” position. It locks the ignition, and

prevents normal use of the steering

wheel after the key is removed.

• CVT vehicles

The gearshift lever must be in the “P”

(Park) position to turn the key to the

“LOCK” position. It locks the ignition and

prevents normal use of the steering

wheel and gearshift lever.

WARNING

To avoid possible injury, do not oper-

ate controls by reaching through the

steering wheel.

EXAMPLE

Turn to “LOCK”

Push

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды