MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 173

Страница: 173 / 324

5-1

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Fuel Filler Cap

68PM05001

68PH00574

The fuel filler cap is located on the left rear

side of the vehicle. The fuel filler door can

be unlocked by pulling up the opener lever

located on the outboard side of the driver’s

seat and locked by simply closing the door.

57L51093

To remove the fuel filler cap:

1) Open the fuel filler door.

2) Remove the cap by turning it counter-

clockwise.

68PH00502

NOTE:

The cap holder (1) holds the fuel filler cap

(2) by hooking the groove (3) when refuel-

ing.

To reinstall the fuel filler cap:

1) Turn the cap clockwise until you hear

several clicks.

2) Close the fuel filler door.

EXAMPLE

CAUTION

Remove the fuel filler cap slowly. The

fuel may be under pressure and may

spray out, causing injury.

Open

EXAMPLE

WARNING

Fuel is extremely flammable. Do not

smoke when refueling, and make

sure there are no open flames or

sparks in the area.

(1)

(2)

(3)

(1)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды