MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 140

Страница: 140 / 324

3-10

OPERATING YOUR VEHICLE

68PH0-74E

Parking Brake Reminder Buzzer

A buzzer sounds intermittently to remind

you to release the parking brake if you

start the vehicle without releasing the park-

ing brake. Make sure that the parking

brake is fully released and the brake sys-

tem warning light turns off.

Pedal

Manual transaxle

80J2121

CVT

80J2122

Clutch Pedal (1)

(For manual transaxle)

The clutch pedal is used to disengage the

drive to the wheels when starting the

engine, stopping, or shifting the gearshift

lever. Depressing the pedal disengages

the clutch.

Brake Pedal (2)

Your vehicle is equipped with front disc

brakes and rear drum brakes. Depressing

the brake pedal applies both sets of

brakes.

You may hear occasional brake squeal

when you apply the brakes. This is a nor-

mal condition caused by environmental

factors such as cold, wet, snow, etc.

Accelerator Pedal (3)

This pedal controls the speed of the

engine. Depressing the accelerator pedal

increases power output and speed.

WARNING

When parking the vehicle in

extremely cold weather, the following

procedure should be used:

1) Set the parking brake.

2) Manual transaxle - turn off the

engine, then shift into reverse or

first gear.

CVT - shift into “P” (Park) and turn

off the engine.

3) Get out of the vehicle and put

chocks under the wheels.

4) Release the parking brake.

When you return to your vehicle,

you must remember to first set the

parking brake, then remove the

wheel chocks.

WARNING

Do not drive with your foot resting on

the clutch pedal. It could result in

excessive clutch wear, clutch dam-

age, or unexpected loss of engine

braking.

(2)

(3)

(1)

EXAMPLE

(3)

(2)

EXAMPLE

WARNING

If brake squeal is excessive and

occurs each time the brakes are

applied, you should have the brakes

checked by your authorised Maruti

Suzuki workshop.

WARNING

Do not “ride” the brakes by applying

them continuously or resting your

foot on the pedal. This will result in

overheating of the brakes which

could cause unpredictable braking

action, longer stopping distances, or

permanent brake damage.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды