MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 50

Страница: 50 / 324

2-32

BEFORE DRIVING

68PH0-74E

80J2008

NOTE:

The word “CENTER” is marked on the

buckle for the rear center belt. The buckles

are designed so a latch plate cannot be

inserted into the wrong buckle.

60A039

To unfasten the seat belt, push the red

“PRESS” button on the buckle and retract

the belt slowly while attaching a hand to

the belt or/and the latch plate.

Lap Belt

Rear Center Seat Belt

To fasten the belt, pull the latch plate

attached to the seat belt across your hips

and press it straight into the buckle until

you hear a “click”. To reduce the risk of

sliding under the belt during a collision,

position the belt across your lap as low on

your hips as possible and adjust it to a

snug fit.

80JS028

To tighten the belt, pull the free end of the

belt across alongside the lap strap.

EXAMPLE

TO TIGHTEN

Low on hips

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды