MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 279 | Manualshive

Страница: 279 / 324

background image

7-23

INSPECTION AND MAINTENANCE

68PH0-74E

Tubeless Tyres (If equipped)

The vehicle is equipped with Tubeless
Tyres. In tubeless tyre, a thin layer of butyl
rubber is used for lining the inside of the
tubeless tyre. This layer is to prevent air
loss and fulfilling the purpose of tube. The
air pressure is maintained by the sealing
between tyre bead and wheel rim. Tube-
less tyres are having advantage of slow air
loss and preventing sudden deflation while
driving.

Care and maintenance tips for tubeless

tyres

1) Always maintain recommended inflation

pressure. Driving continuously at low
inflation pressure can lead to tyre dam-
age.

2) In case any leakage is found, check for

any nail penetration/valve core dam-
age or rim bent. Damaged wheel must
not be used.

3) In case tyre has run at low pressure, it

must be inspected for any defect.

4) Whenever new tyre is fitted, replace the

valve.

5) If continuous high speed driving is

required, increase tyres pressure by 5
psi over recommended inflation pres-
sure.

6) Never run the tyre beyond TWI (Tread

wear indicator). The tyre is recommen-
ded to be replaced when the remaining
tread has worn to this point. The indica-
tors are spaced across the tread

around the tyre marked by a triangular
symbol (TWI).

7) Always prefer tubeless tyre mounting

machine. In case of manual mounting-
tyre/wheel rim damage may occur.

8) In case of any problem, please get in

touch with authorised Maruti Suzuki
workshop.

Temporary Spare Tire (If equipped)

Your vehicle comes equipped with the tem-

porary spare tire. It is only intended for

temporary emergency use, until the con-

ventional tire can be repaired or replaced.

The inflation pressure of the temporary

spare tire should be checked at least

monthly. At the same time, check that the

tire is stored securely. If it is not, tighten it.

Note that two or more temporary spare

tires should not be used on one vehicle

simultaneously.

WARNING

The temporary spare tire and wheel

are intended for temporary emergency

use only. Continuous use of this spare

can result in tire failure and loss of

control. Always observe these precau-

tions when using this spare:

• Your vehicle will handle differently

with this temporary spare.

• Do not exceed 80 km/h speed (Only

vehicle with 195/55R16 87H tire).

• Replace this spare with a standard

tire and wheel as soon as possible.

• Use of this spare may reduce

ground clearance.

• Set the specified tire pressure indi-

cated on the tire information label

located on the driver’s door lock

pillar.

• Do not use tire chains on the tem-

porary spare. If you must use tire

chains, rearrange the wheels so

standard tires and wheels are fitted

to the front axle.

• The temporary spare tire has a

much shorter tread life than the

conventional tires on your vehicle.

Replace the tire as soon as the

tread wear indicator appears.

• When replacing the temporary

spare tire, use a replacement tire

with the exact same size and con-

struction.

«
...
277
278
279
280
281
...
»

Содержание BALENO 2017





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BALENO 2017

Бренд: Camcar Страницы: 6

Бренд: Thule Страницы: 8

Бренд: AC Schnitzer Страницы: 20

Бренд: P-Invent Страницы: 4

Бренд: tams elektronik Страницы: 19

Бренд: Xpresskit Страницы: 18

Бренд: Thule Страницы: 3

Бренд: Paccar Страницы: 63

Бренд: Rugged Ridge Страницы: 2

Бренд: S&B Filters Страницы: 4

Бренд: Mazda Страницы: 3

Бренд: Needit Страницы: 2

KIT ParkingSensor 814

Бренд: Gemini Страницы: 6

T13 Outback Frontal Protection System

Бренд: T.J.M. Страницы: 18

Бренд: Audi Страницы: 4

Бренд: Quadratec Страницы: 2

Бренд: HAKR Страницы: 2

Бренд: Ranger design Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды