MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 197

Страница: 197 / 324

5-25

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Temperature selector (1)

68PH00551

Push the temperature selector (1) to adjust

the temperature.

Blower speed selector (2)

68PH00552

Air flows out at a higher rate when you

press the upper switch and at a lower rate

when you press the lower switch.
If the “AUTO” switch (8) is pushed, the

blower speed will vary automatically as the

climate control system maintains the

selected temperature.

Air intake selector (3)

68PH00553

Push the air intake selector (3) to change

between the following modes.
If the “AUTO” switch (8) is pushed, the air

intake will vary automatically as the climate

control system maintains the selected tem-

perature.

NOTE:

When you select the recirculated air mode,

the automatic operation system is deacti-

vated if you push the “AUTO” switch (8).

RECIRCULATED AIR (a)

When this mode is selected, outside air is

shut off and inside air is recirculated. This

mode is suitable when driving through an

area with polluted air such as a tunnel, or

when attempting to quickly cool down the

vehicle.

(1)

EXAMPLE

(2)

EXAMPLE

(3)

(a)

(b)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды