MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 142

Страница: 142 / 324

3-12

OPERATING YOUR VEHICLE

68PH0-74E

Warm engine

Crank the engine by turning the ignition

key to “START”. Release the key when the

engine starts.

Caution when stopping the engine with

turbocharger

When stopping the engine after climbing or

high speed driving, let the engine idle for

about one minute or more (If it is not pro-

hibited) to cool down the turbocharger and

engine oil. This is to prevent the engine oil

from over-deteriorating. Deteriorated

engine oil will damage the bearings of the

turbocharger.

Restarting diesel engine after fuel-

empty stop

If the engine stops and the low fuel warn-

ing light and the malfunction indicator light

come on, use the following procedure:

1) Fill the fuel tank.

2) Hold the ignition key in “ON” position for

5-10 seconds to feed fuel.

3) Perform above engine starting proce-

dure to start the engine.

If the malfunction indicator light still comes

on after the engine started, there may be

some problem with the engine. Ask your

authorised Maruti Suzuki workshop to

have the engine inspected.

NOTE:

The engine of manual transaxle vehicle will

not start unless the clutch pedal is

depressed.

Starting the Engine
(Vehicle with keyless push
start system)

Before Starting the Engine

68PH00309

1) Make sure the parking brake is set fully.

2) Shift to “N” (Neutral) and fully depress

the clutch pedal. Hold the clutch and

brake pedals fully depressed.

NOTE:

The engine of manual transaxle vehicle will

not start unless the clutch pedal is

depressed.

68PH00303

3) The “PUSH START SWITCH” message

will appear on the information display in

the instrument cluster. Push the engine

switch (1). When the engine is started,

the starter motor will automatically stop.

NOTE:

• You do not need to keep the engine

switch pressed to start the engine.

• The engine of a manual transaxle vehi-

cle will not start unless the clutch pedal

is depressed.

• During the engine starting procedure,

messages

on the information display will

EXAMPLE

(1)

EXAMPLE

WARNING

Make sure that the parking brake is

set fully and the transaxle is in “N”

(Neutral) before attempting to start

the engine.

NOTICE

• Do not depress the accelerator

during the engine starting proce-

dure.

• If the engine does not respond

when you try to start it with the

engine switch or if the engine

switch repeats cycling through the

“LOCK”(OFF) - “ACC” - “ON”

mode, the vehicle battery may be

discharged. Check the voltage of

the vehicle battery before trying

again.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды