MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 227

Страница: 227 / 324

5-55

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Phone registration

NOTE:

• Up to 5 phones can be registered.

• To set up a new phone, disconnect the

audio player from the unit. Connect the

audio player again after phone setup is

completed if necessary.

• When failed to establish the pairing

within 120 seconds, the connecting

operation will be canceled. Please try

again or refer to the manual of the phone

in use for how to establish the pairing

with the phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Pairing”,

and press the knob (1) to determine the

selection.

4) Select “MY CAR” from the Bluetooth

menu of the phone and establish the

pairing.

Refer to the manual of the phone in use

for further information.

5) Enter the Passkey displayed on the unit

to the phone.

6) When the pairing with the phone is

established, automatic transfer of the

phonebook and the call history

becomes selectable. The automatic

transfer starts with “Yes” and it does not

with “No”.

7) Press the On Hook button (8).

NOTE:

• When selecting “Go Back” or pressing

the back button (4), the previous menu

will be displayed.

• When additionally registering a phone,

operate the same step from 1).

Receiving a call

Press the Off Hook button (7) to receive a

call.

Ending a call

Press the On Hook button (8) to end a call.

Rejecting a call (Only for supported

models)

Press the On Hook button (8) to reject a

incoming call.

Mute of hands-free microphone

Press the MUTE switch (9) to mute the

microphone. To cancel the mute, press the

MUTE switch (9) again.

Adjusting the listening volume

• Turn the VOL PUSH POWER knob (2)

during a call.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press the VOL switch (10) during a call.

Pressing “+” of the switch increases the

volume, pressing “-” of the switch

decreases the volume.

Adjusting the ring volume

• Turn the VOL PUSH POWER knob (2)

while a call coming in.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press the VOL switch (10) during a call.

Pressing “+” of the switch increases the

volume, pressing “-” of the switch

decreases the volume.

Adjusting the call or ringtone volume

Follow the instructions below to adjust the

call or ringtone volume.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

To use the hands-free function with this

unit, it is required to register the phone

in advance.

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды