MARUTI SUZUKI BALENO 2017 Скачать руководство пользователя страница 193

Страница: 193 / 324

5-21

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Air intake selector (4)

68PH00548

This selector is used to select the following

modes.

Fresh Air (f)

When this mode is selected, the indicator

light will go off and outside air is used.

Recirculated Air (g)

When this mode is selected, the indicator

light will come on, outside air is shut out

and inside air is recirculated. This mode is

suitable when driving through dusty or pol-

luted air such as in a tunnel, or when

attempting to quickly cool down the inte-

rior.

“FRESH AIR” and “RECIRCULATED AIR”

are switched alternately each time the air

intake selector is pushed.

NOTE:

If you select “RECIRCULATED AIR” for an

extended period of time, the air in the vehi-

cle can become contaminated. Therefore,

you should occasionally select “FRESH

AIR”.

Air conditioning switch (5)

To turn on the air conditioning system, set

the blower speed selector to a position

other than off and push in the “A/C” switch.

With this “A/C” switch operation, a indica-

tor light will come on when the air condi-

tioning system is on. To turn off the air

conditioning system, push the “A/C” switch

again.
During operation of the air conditioner, you

may notice slight changes in engine

speed. These changes are normal, the

system is designed so that the compressor

turns on or off to maintain the desired tem-

perature.
Less operation of the compressor results

in better fuel economy.

System Operating Instructions

Natural ventilation

Select “VENTILATION” and “FRESH AIR”,

the temperature selector to the desired

temperature position, and the blower

speed selector to off. Fresh air will flow

through the vehicle during driving.

Forced ventilation

The control settings are the same as for

natural ventilation except you set the

blower speed selector to a position other

than off.

Normal heating (using outside air)

Select “HEAT” and “FRESH AIR”, the tem-

perature selector to the desired tempera-

ture position and the blower speed selector

to the desired blower speed position. Set-

ting the blower speed selector to a higher

blower speed position increases heating

efficiency.

Quick heating (Using recirculated air)

The control settings are the same as for

normal heating except you select “RECIR-

CULATED AIR”. If you use this heating

method for an extended period of time, the

air in the vehicle can become contami-

nated and the windows can become misty.

Therefore, use this method only for quick

heating and change to the normal heating

method as soon as possible.

(f)

(g)

EXAMPLE

Содержание BALENO 2017





































































































































































































































































































































Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды

MARUTI SUZUKI BALENO 2017, Руководство пользователя

Результаты поиска

Содержание BALENO 2017

Отзывы:

Похожие инструкции для BALENO 2017

Бренды по названию

Популярные бренды