Krone 870 HDP Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 568

Krone 870 HDP Скачать руководство пользователя страница 83

Commissioning

83

Pos: 77.9 /Überschriften/Überschriften 2/F-J/HH ydraulischen Stützfuß anbauen @ 193\mod_1383215414302_78.docx @ 1646685 @ 2 @ 1

8.1

Attaching Hydraulic Parking Jack

Pos: 77.10 /BA/Erstinbetriebnahme/Groß packenpressen/Bei Ausführung hydraulischer Stützfuß @ 193\mod_1383214866332_78.docx @ 1646602 @ @ 1

With hydraulic parking jack design.

Pos: 77.11 /BA/Erstinbetriebnahme/Groß packenpressen/H ydr aulischen Stützfuß anbauen Bild @ 193\mod_1383214808495_78.docx @ 1646573 @ @ 1

Fig. 43

Pos: 77.12 /BA/Erstinbetriebnahme/Groß packenpressenH ydraulischen Stützfuß anbauen T ext T1 @ 326 \mod_1425977815714_78.docx @ 2502941 @ @ 1

• Attach the crane to the suspension point (I) on the drawbar.
• To raise the support jack (2), slightly raise the drawbar, shift support jack entirely upward

and secure with socket pin (3).

• To lower the drawbar on the ground, place sufficiently dimensioned square blocks under the

front drawbar beam (4) and lower the drawbar.

• Lay the hydraulic hoses (5) to the outside.
• To remove the support jack, screw out the four screws (6), remove the support jack and put

it down to the side.

•  Insert the hydraulic support jack (7) at the same position.
•  To raise the hydraulic support jack, attach the support jack using the crane (II) and raise it.
•  Mount screws (6) and detent edged washers and secure with detent edged washers and

nuts.

Tighten the screws with corresponding tightening torque.

Pos: 77.13 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
81
82
83
84
85
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов