manualshive.com logo in svg

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 322 / 568

Поделиться
Скачать
Krone 870 HDP Скачать руководство пользователя страница 322

Maintenance - Gearbox

 

 

322 

 

Pos: 124.32 /Ü berschriften/Ü berschriften 2/P-T /PPick-up-Getriebe @ 24\mod_1241589499831_78.docx @ 246271 @ 2 @ 1 

 

22.4 

Pick-up gearbox  

Pos: 124.33 /Ü berschriften/Z wischenüberschriften/A- EBei Ausführung ohne Schnei dwerk @ 157\mod_1364379318831_78.docx @ 1387595 @  @ 1 

 

Design without cutting system 

Pos: 124.34 /BA/Wartung/Öl kontr olle_Wechsel/Groß packenpresse/Pick-up Getriebe Anbri ngungsort @ 24\mod_1241589606081_78.docx @ 246295 @  @ 1 

 

The upper (4a) and lower (4b) Pick-up gearboxes are located on the right side of the machine. 

Pos: 124.35 /BA/Wartung/Öl kontr olle_Wechsel/Groß packenpresse/Pick-up Getriebe oben/unten Bil d mitLeg ende 4x4 / 1290 HD PII (2014-10-23 08:52:10) @ 158\mod_1364993139471_78.docx @ 1395904 @  @ 1 

 

1

2

3

 

Fig. 235 
1) 

Inspection screw / control hole 

2) 

Drain plug 

3) 

Filler plug / filling hole  

4a)  Pick-up gearbox top 

4b)  Pick-up gearbox bottom 

 

 

 

Pos: 124.36 /BA/Wartung/Öl kontr olle_Wechsel/Öl kontr olle / Öl wechsel  Intervall: siehe Kapitel Wartung „ Wartungstabelle“ @ 134\mod_1350483605921_78.docx @ 1188115 @  @ 1 

 

Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table” 

Pos: 124.37 /BA/Wartung/Öl kontr olle_WechselÖlqualität/Öl menge: siehe Kapitel  T echnische D aten der M aschine @ 371\mod_1441958324612_78.docx @ 2710777 @  @ 1 

 

Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating 

Materials” 

Pos: 124.38 /BA/Wartung/Öl kontr olle_Wechsel/Altöl entsorgung: siehe Kapitel Sicherheit „Betri ebsstoffe“ @ 280\mod_1405428392269_78.docx @ 2152765 @  @ 1 

 

Used oil disposal: see chapter Safety "Consumables" 

Pos: 124.39 /BA/Sicher hei t/8. Vor aussetzungen/H andl ungsanweisung für alle Maschi nen/H andl ungsanweisung: Maschi ne stillsetzen und sicher n @ 274\mod_1404365253849_78.docx @ 2065151 @  @ 1 

 

•  Shut down and safeguard the machine, see chapter Safety -> Safety routines, "Shutting 

down and safeguarding the machine". 

Pos: 124.40 /BA/Wartung/Öl kontr olle_WechselÖl kontroll e N EU über Kontrollschraube @ 140 \mod_1355141753680_78.docx @ 1244582 @  @ 1 

 

Oil level check: 

•  Screw out inspection screw. 
•  Oil level up to control hole. 

If the oil reaches the control hole: 

•  Screw in the inspection screw and tighten it securely. 

If the oil does not reach the control hole:

 

•  Screw out filler plug. 
•  Top up oil via oil filling hole until the control hole is reached. 
•  Screw in the inspection screw and the filler plug and tighten them securely. 

Pos: 124.41 /BA/Wartung/Öl kontr olle_WechselÖl wechsel  NEU @ 140\mod_1355142057277_78.docx @ 1244610 @  @ 1 

 

Oil change: 

Collect escaping oil in a suitable container. 
•  Screw out oil drain plug and drain the oil. 
•  Screw out inspection screw and filler plug. 
•  Screw in oil drain plug and tighten it securely. 
•  Top up new oil via oil filling hole until the control hole is reached. 
•  Screw in the inspection screw and the filler plug and tighten them securely. 
 

Pos: 124.42 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов