manualshive.com logo in svg

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 304 / 568

Поделиться
Скачать
Krone 870 HDP Скачать руководство пользователя страница 304

Maintenance

 

 

304 

 

Pos: 98.16 /Ü berschriften/Ü berschriften  2/K-O/MM esser wechsel @ 8\mod_1219657285958_78.docx @ 119937 @ 2 @ 1 

 

20.4 

Blade Changing  

Pos: 98.17 /BA/War tung/Schnei dwer k/Messer wechsel allgemein von der linken Seite Big Pack @ 275\mod_1404469078762_78.docx @ 2069681 @  @ 1 

 

Blades are changed in the same way on the right and left side of the machine. The procedure 

used on the left side of the machine is described below. The same applies for the right side of 

the machine. 

Pos: 98.18 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 98.19 /BA/Sicherheit/6. Überar beitete Warnhinweise/Warnung - F unkti on Messerbal ken heben/senken betätigen @ 377\mod_1443161811445_78.docx @ 2736379 @  @ 1 

 

 

WARNING! 

Serious injuries caused by moving machine parts 

The blade bar moves by actuating the function “Raise/lower blade bar”. Thus persons could be 

seriously injured. 
•  Make sure that there is no one in the danger zone of the blade bar.  

 

Pos: 98.20 /BA/War tung/Schnei dwer k/Achtung - Schnei dwerk hochfahr en @ 275\mod_1404469396832_78.docx @ 2069710 @  @ 1 

 

 

ATTENTION! 

You many damage the cutting system if you raise it without first retracting and locking 

the knife drawers. 

•  Ensure that both knife drawers are properly pushed in and locked before the cutting 

system is raised. 

 

Pos: 98.21.1 /BA/Wartung/Schnei dwer k/Messer wechsel Bild @ 275\mod_1404401306487_78.docx @ 2068091 @  @ 1 

 

5

BPHS0300

3

6

 

Fig. 222 

Pos: 98.21.2 /BA/Wartung/Schnei dwer k/Schnei dwer k absenken  zÜ @ 275\mod_1404468973233_78.docx @ 2069532 @  @ 1 

 

Lowering the cutting system 

Pos: 98.21.3 /BA/Wartung/Schnei dwer k/Schnei dwer k absenken: Medium–El ektr oni k @ 356\mod_1438698331389_78.docx @ 2654895 @  @ 1 

 

Medium electronics 

•  Actuate the control unit (

) on the tractor until the cutting unit has been fully lowered. 

Pos: 98.21.4 /Layout Module  /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 98.21.5 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/Gr oß packenpr essen/Komfort-El ektr oni k @ 61\mod_1299223046976_78.docx @ 570919 @  @ 1 

 

Comfort - Electronic 

Pos: 98.21.6 /BA/Info-Center/CCI-ISOBUS-T er minal/CCI- BiG Pack/F unkti onstasten F 1 bis F  12M esserbal ken freischal ten @ 352\mod_1437392672909_78.docx @ 2634130 @  @ 1 

 

Release 

•  To release the blade bar, press 

. 

The symbols 

,

 are shown on the display. 

Pos: 98.21.7 /BA/Info-Center/CCI-ISOBUS-T er minal/CCI- BiG Pack/F unkti onstasten F 1 bis F  12M esserbal ken senken @ 352\mod_1437393051647_78.docx @ 2634192 @  @ 1 

 

Lowering 

•  To lower the blade bar, press and hold 

.   

Pos: 98.21.8 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 98.21.9 /BA/Wartung/Schnei dwer k/Schnei dwer k absenken: Komfort-El ektroni k Ü ber di e T asten @ 275\mod_1404467742434_78.docx @ 2069479 @  @ 1 

 

Using the pushbuttons on the machine 

•  To lower the blade bar, press the 

 pushbutton until the blade bar is fully lowered. 

Pos: 98.21.10 /Layout M odul e /----------------Leerzeil e 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @  @ 1 

 

 

Pos: 98.21.11 /BA/Wartung/Schneidwer k/Einzel messersicherung entl asten @ 275\mod_1404467559772_78.docx @ 2069451 @  @ 1 

 

Releasing the single blade locking device 

•  Shut down and safeguard the machine, see chapter Safety -> Safety routines "Shutting 

down and safeguarding the machine". 

•  Attach the special tool (4) to the upper or knife selection (1, 2). 

 

CAUTION!

 Risk of injury due to spring pressure on the special tool. If you release it too soon, 

you can injure yourself. 

 

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов