manualshive.com logo in svg

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 258 / 568

Поделиться
Скачать
Krone 870 HDP Скачать руководство пользователя страница 258

Settings

 

 

258 

 

Pos: 93.45.1 /Ü berschriften/Ü berschriften 2/K-O/MM ulti-Bale ei nstellen @ 272\mod_1403516170463_78.docx @ 2050813 @ 2 @ 1 

 

19.5 

Adjusting the MultiBale  

Pos: 93.45.2 /BA/Ei nstellungen/Groß packenpresse/M uti Bal e/Position zweite N adelschwing e / Anschlag Bild @ 24\mod_1241443960165_78.docx @ 245076 @  @ 1 

 

 

Fig. 176 

Pos: 93.45.3 /BA/Ei nstellungen/Groß packenpresse/M uti Bal e/Einstell ung Position zweite N adelschwing e @ 24\mod_1241444369290_78.docx @ 245100 @ 3 @ 1 

 

19.5.1 

Setting the position of the second needle yoke  

The tube (2) of the needle yoke (3) has to be located in the trough (4). If this is not the case, 

please proceed as follows: 
•  Check the knotter needle setting relative to the knotter, and adjust, if and when necessary 

(refer to chapter Settings "Needle setting"). 

•  Adjust the needle yoke brake (1) in longitudinal position in the oblong hole (15) so that the 

tube (2) of the needle yoke (3) is in the end setting of the tie immediately after the trough (4) 

of the needle yoke brake (1) 

 

Pos: 93.45.4 /BA/Ei nstellungen/Groß packenpresse/M uti Bal e/Einstell ung Anschl ag @ 24\mod_1241445271930_78.docx @ 245124 @ 3 @ 1 

 

19.5.2 

Setting the stop 

•  In this setting the distance between the tube (2) of the needle yoke (3) and the obstruction 

should be (5) x = 8 - 15 mm. Adjust the stop (5) if necessary using washers (6) 

Pos: 93.45.5 /BA/Ei nstellungen/Groß packenpresse/M uti Bal e/Einstell ung H öhe der Nadelschwingenbremse @ 24\mod_1241498230617_78.docx @ 245177 @ 3 @ 1 

 

19.5.3 

Setting the height of the needle yoke brake 

 

Fig. 177 
•  During the infeed of the needle yoke (3), the roller (7) of the needle yoke brake (1) has to 

make contact with the lower third of the tube (2). The height of the needle yoke brake (1) 

can be changed by placing washers under the clamping screw stop (8). 

•  Pre-tension the spring (9) of the needle yoke brake (1) to a dimension y = 115 - 120 mm 
 

Pos: 93.45.6 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов